Leading 10 common forklift accidents ， forklift operation should pay attention to these matters ！.

Do not undervalue the forklift at the workplace. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight blocked the motorist's view, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to preserve the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift cargo surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be risk-free before beginning.
3. When the forklift begins with a tons, the driver must first verify that the lots is steady and dependable.
4. The beginning must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not raise the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork has to not be increased expensive, which will influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving position before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest setting that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique situations, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it ought to be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard objects with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to additionally be examined and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free switching";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift personnel bring the goods and move forward, if they run into huge or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the Electric Forklift Truck for Warehouse fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the very same length as the obstacle ought to be within 20 meters at Electric Forklift Truck for Warehouse each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844